YATO clamp multimeter TRUE RMS, 0–600 A AC

Official YATO Dealer
- 100% genuine products
- Manufacturer warranty
- Professional consultation
Technical Specifications
Dimensions: 185 x 71 x 35 mm
Material: ABS
Application: electrical work
Operating temperature range: 0–40 °C
Storage temperature: −10 to +50 °C
Power supply: battery
Battery type: 3 × 1,5 V AAA
Weight: 0,15 kg
Display type: LCD
Data hold: yes
Continuity test: 0–50 Ω
Conductivity test: yes
LED backlight: yes
Front light: yes
Operating relative humidity Rh: <75%
Low battery indicator: yes
AC voltage: 0–600 V AC
DC voltage: 0–600 V DC
Resistance: 0–40 MΩ
Diode test: yes
Battery test: yes
AC current: 0–600 A
Sampling rate: 3 times per second
TRUE RMS: yes
Automatic range selection: yes
Maximum clamp opening: 26 mm
Maximum diameter of cable measurable with the clamp: 26 mm
Audible signal: yes
Display reading range: 3999
Automatic shut-off: 20 min
Non-contact AC voltage detection NCV: yes
Number of display digits: 4
Storage relative humidity: <85%
Temperature range for stated accuracy: 18–28 °C; relative humidity <75%
DC voltage input impedance: 10 MΩ
AC voltage input impedance and frequency: 10 MΩ; 40–1000 Hz
DC voltage ranges, resolution and accuracy: 400 mV (0,1 mV); 4 V (0,001 V), 40 V (0,01 V), 400 V (0,1 V): ±(0,8% + 3); 600 V (1 V): ±(1,0% + 5)
AC voltage ranges, resolution and accuracy: 4 V (0,001 V), 40 V (0,01 V), 400 V (0,1 V): ±(1,2% + 3); 600 V (1 V): ±(1,0% + 5)
DC voltage overload protection: 600 V DC
AC voltage overload protection: 600 V AC RMS
AC current measurement frequency: 50–60 Hz
AC current ranges, resolution and accuracy: 4 A (0,001 A): ±(2,5% + 5); 40 A (0,01 A); 600 A (1 A)
Resistance ranges, resolution and accuracy: 400 Ω (0,1 Ω): ±(1,5% + 3); 4 kΩ (0,001 kΩ), 40 kΩ (0,01 kΩ), 400 kΩ (0,1 kΩ), 4 MΩ (0,001 MΩ): ±(0,8% + 3); 40 MΩ (0,01 MΩ): ±(1,5% + 3)
Accuracy expression: ± (% of reading + number of least significant digit units)
The YATO TRUE RMS clamp multimeter is designed for basic and advanced electrical measurements and measures alternating current up to 600 A.
Automatic range selection sets a suitable range for the measured value.
The clamp meter can measure alternating current around a single wire using the induction method.
There is no need to interrupt the circuit or disconnect the device from the power supply for measurement.
When measuring alternating current, the device uses the TRUE RMS method.
The multimeter can also measure AC and DC voltage and resistance.
The device can perform a diode test and check circuit continuity. Diode test parameters are IF 1 mA and UR 2,3 V. When checking continuity, the device emits an audible signal for resistance below 50 Ω.
Voltage detection and phase checking
The non-contact NCV function detects AC voltage without making electrical contact with a probe.
The indicator function can be used to check for the presence of a phase.
Test probes and construction
The test probes are 12 cm long, and the total length of their leads, including the probes, is 85 cm.
The diameter of the leads, including insulation, is 3,5 mm, and the insulation is made of PVC.
A pouch is included.
Dimensions: 185 x 71 x 35 mm
Material: ABS
Application: electrical work
Operating temperature range: 0–40 °C
Storage temperature: −10 to +50 °C
Power supply: battery
Battery type: 3 × 1,5 V AAA
Weight: 0,15 kg
Display type: LCD
Data hold: yes
Continuity test: 0–50 Ω
Conductivity test: yes
LED backlight: yes
Front light: yes
Operating relative humidity Rh: <75%
Low battery indicator: yes
AC voltage: 0–600 V AC
DC voltage: 0–600 V DC
Resistance: 0–40 MΩ
Diode test: yes
Battery test: yes
AC current: 0–600 A
Sampling rate: 3 times per second
TRUE RMS: yes
Automatic range selection: yes
Maximum clamp opening: 26 mm
Maximum diameter of cable measurable with the clamp: 26 mm
Audible signal: yes
Display reading range: 3999
Automatic shut-off: 20 min
Non-contact AC voltage detection NCV: yes
Number of display digits: 4
Storage relative humidity: <85%
Temperature range for stated accuracy: 18–28 °C; relative humidity <75%
DC voltage input impedance: 10 MΩ
AC voltage input impedance and frequency: 10 MΩ; 40–1000 Hz
DC voltage ranges, resolution and accuracy: 400 mV (0,1 mV); 4 V (0,001 V), 40 V (0,01 V), 400 V (0,1 V): ±(0,8% + 3); 600 V (1 V): ±(1,0% + 5)
AC voltage ranges, resolution and accuracy: 4 V (0,001 V), 40 V (0,01 V), 400 V (0,1 V): ±(1,2% + 3); 600 V (1 V): ±(1,0% + 5)
DC voltage overload protection: 600 V DC
AC voltage overload protection: 600 V AC RMS
AC current measurement frequency: 50–60 Hz
AC current ranges, resolution and accuracy: 4 A (0,001 A): ±(2,5% + 5); 40 A (0,01 A); 600 A (1 A)
Resistance ranges, resolution and accuracy: 400 Ω (0,1 Ω): ±(1,5% + 3); 4 kΩ (0,001 kΩ), 40 kΩ (0,01 kΩ), 400 kΩ (0,1 kΩ), 4 MΩ (0,001 MΩ): ±(0,8% + 3); 40 MΩ (0,01 MΩ): ±(1,5% + 3)
Accuracy expression: ± (% of reading + number of least significant digit units)
Returns & Warranty
Product returns
14-day right of withdrawal. Terms for consumers and business customers.
Return instructionsWarranty
All products come with manufacturer warranty as required by law.
We ship from Estonia






Delivery time depends on stock
This product has no reviews yet. Be the first to rate it.
Product description
The YATO TRUE RMS clamp multimeter is designed for basic and advanced electrical measurements and measures alternating current up to 600 A.
Automatic range selection sets a suitable range for the measured value.
The clamp meter can measure alternating current around a single wire using the induction method.
There is no need to interrupt the circuit or disconnect the device from the power supply for measurement.
When measuring alternating current, the device uses the TRUE RMS method.
The multimeter can also measure AC and DC voltage and resistance.
The device can perform a diode test and check circuit continuity. Diode test parameters are IF 1 mA and UR 2,3 V. When checking continuity, the device emits an audible signal for resistance below 50 Ω.
Voltage detection and phase checking
The non-contact NCV function detects AC voltage without making electrical contact with a probe.
The indicator function can be used to check for the presence of a phase.
Test probes and construction
The test probes are 12 cm long, and the total length of their leads, including the probes, is 85 cm.
The diameter of the leads, including insulation, is 3,5 mm, and the insulation is made of PVC.
A pouch is included.
Shipping & Delivery
We ship from Estonia






Delivery time depends on stock
Returns & Warranty
Product returns
14-day right of withdrawal. Terms for consumers and business customers.
Return instructionsWarranty
All products come with manufacturer warranty as required by law.
Reviews
This product has no reviews yet. Be the first to rate it.

YATO clamp multimeter TRUE RMS, 0–600 A AC
YT-730935